General Finishes Enduro White Poly Water-Based Topcoat - Quart (Satin)

General Finishes Enduro White Poly Water-Based Topcoat - Quart (Satin)

$ 43.33

Have questions? Give us a call at 260-637-0054.

Enduro White Poly is a water-based topcoat for professionals and industrial facilities wanting a durable, fast-drying white cabinet finish. It is formulated to spray from the can without having to thin and builds quickly. Suitable for fiberglass, MDF, and all woods.

Use over General Finishes Stain Blocker. White and Clear can be used as tint bases to achieve most standard paint deck colors. Can be used as a stand alone finish!

Also available in gallons.

Don't forget sandpaper!

Note: Do not use any type of clear topcoat over GF White Poly, as it may cause yellowing.

Shipping Notice: During periods of extreme cold, OakTree may temporarily hold water-based products to prevent them from freezing during transit. As a result, shipping times may vary based on local and national weather conditions.

Features
  • Meet or exceed KCMA standards
  • Self-crosslinking and self-sealing
  • Thinner formulation for easy spraying
  • Fast-drying, durable, and abrasion-resistant
Specs

Sheen: Satin
Tint-able?: Yes
Interior/Exterior: Interior only
Coats: 3
Application method: Spray
Spray tip size: HVLP 1.3 mm - 1.5 mm
Dry time (touch): 30+ min.
Dry time (recoat): 2+ hr.
Dry time (light use): 7-10 days
Dry time (cure): 21 days @ 70°F, 50% humidity
Thin with: Water, GF Extender
Coverage: 112.5 sq. ft. per quart
Viscosity: Medium
Viscosity (cPs): 600-800

Preparation

Raw Wood

  1. Sand with 120-grit sandpaper, followed by 150 or 220-grit.
  2. Remove dust.

Sealed Surface

  1. Scuff clean with a non-woven abrasive pad & 50:50 mix of denatured alcohol & water.
  2. Dry 1-2 hours.
  3. Sand lightly with 220-320-grit sanding sponge.
  4. Remove dust.
Directions
  1. Wear a mask and work in a ventilated space.
  2. Before spraying, strain through a fine-mesh filter. Spray wet films at 3-5-mil thickness. Medium air cap. Compressed air: .040, HVLP: .043 -.051 or Airless: .1 -.15.
  3. Keep your gun at a 90° angle, 6-8" from the surface. On large, flat areas, use wet, even patterns 6-8" wide. For narrow surfaces, reduce the fan pattern to 2-3" wide to reduce overspray.
  4. Overlap each pass 25% to conceal lines.
  5. If a faster build is desired over raw wood, use General Finishes Sanding Sealer for the first coat, followed by 2 coats of White Poly.
  6. Dry time is based on ideal conditions: 70°F/21°C; 50% humidity. Tack free 5-10 minutes. Ready to sand 30-45 minutes. Recoat in 1-2 hours. Be sure to allow adequate dry time. You can tell if a water-based finish is dry if it forms a powder when lightly sanded with a 220-320 sanding sponge. If in doubt, wait longer. Rushing the dry time can cause "blush," which is clouding in the finish due to moisture trapped between the layers.
  7. Finish sand between coats with a 220-320 sanding sponge to improve smoothness and adhesion.
  8. Remove dust with a vacuum, compressed air, an oil-free tack cloth or a water-dampened rag.
Video

SKU: B242-L Quart