General Finishes Enduro Conversion Varnishes - Gallon

Price
$ 150

Have questions? Give us a call at 260-637-0054.

Sheen:

Water-based Conversion Varnish is a clear drying, two-component, post-catalyzed urethane topcoat for professional use when ultimate durability is needed. Use this wood finish for high-use projects that receive more use, such as bars, commercial tabletops, bathroom vanities, around dishwashers, kitchen cabinets or high-moisture areas. Suitable for interior and exterior projects, CV is the most durable water‐based topcoat in GF’s product line and significantly outperforms solvent‐based CV’s.

Recommended uses: Interior or exterior cabinets, trim, doors, furniture, table tops, and bar tops. Use over raw wood, stain, and non-white painted surfaces.

Don't forget your sandpaper!

Specs

Product Colors: Water White in can (dries clear)
Base Type: Water
Ambering: No
Sheen: Flat (10 or less), Satin (25-35), Semi-Gloss (50-60), Gloss (80+)
Interior or Exterior: Interior/Exterior
Tintable: No
Type: Urethane/Acrylic Blend
Coats: 3 coats
Application Method: Spray
Brushable: No
Usable over existing finishes: Yes
Spray Tip Sizes: HVLP 1.1mm-1.3mm
Dry Time - Touch: 30+ min.
Dry Time - Recoat: 2+ hrs.
Dry Time - Light Use: 72 hrs.
Dry Time - Cure: 7 days
Coverage: 450 sq. ft.
Viscosity: Medium
Viscosity (cPs): 350-450
Durability (Highest, High, Medium, Low): Highest

Preparation

Raw Wood

  • Sand no finer than 220 grit.
  • Remove dust.

Sealed Surface

  • Scuff clean with a non-woven abrasive pad & 50:50 mix of denatured alcohol & water.
  • Dry 1-2 hours.
  • Sand lightly with 220-320-grit sanding sponge.
  • Remove Dust
Directions
  • Work in a well-ventilated area.
  • Stir thoroughly to reincorporate solids that have settled to the bottom of the can using a power drill and mixer (recommended) or by hand with a paint stick. Do not shake. 
  • Test for adhesion when applying over an existing finish.
  • Thin as desired, with distilled water (before or after mixing with NCO catalyst); start with 5%,adding up to 10% by volume.
  • Increase open time, if needed, with 10-15% by volume of General Finishes Extender if allowed by local regulations. GF Extender can be used to improve flow and leveling, and increase open time, which is helpful in dry climates. California Residents: Adding more than 2% of GF Extender will make the product non-compliant per SCAQMD Regulations. GF assumes no liability for the improper use of these products.
  • Slowly add up to 10% NCO Catalyst by volume (3.2 oz. per quart; 12.8 oz. per gallon) to Conversion Varnish while stirring thoroughly. Allow 2-3 minutes when mixing with a power drill, or 5 minutes when mixing by hand with a paint stick. Use gloves and protective eyewear when mixing. Mix only what you are going to use and clean the spray gun immediately after use. The finish can only be mixed once, and the leftover product will solidify after 6-8 hours. DO NOT store in a closed container to avoid pressure build-up.
  • Let Conversion Varnish sit for 15 minutes.
  • Apply 3 coats. For high-moisture areas, apply 4 coats. Additional coats will not improve durability.
  • Spray application: Before spraying, strain topcoat through a fine-mesh filter. Spray wet films at 3-5-mil thickness. HVLP: 1.1mm-1.3mm spray tip, medium air cap. Verify tip sizes with your equipment supplier. Spray tip recommendations. Keep your gun at a 90° angle, 6-8" from the surface. On large, flat areas, use wet, even patterns 6-8" wide. For narrow surfaces, reduce the fan pattern to 2-3" wide to reduce overspray. Overlap each pass 25% to conceal lines. NOTE: Conversion Varnish is used with NCO catalyst. When using a spray-gun, wear self-contained breathing apparatus. In the event of insufficient ventilation: Wear self-contained breathing apparatus. When respirators are required, select NIOSH/MSHA approved equipment and work in a ventilated space.
  • Face frames on cabinets: Enduro professional products are engineered to be spray-only but can be successfully applied by hand to cabinet face frames or edges with a pad applicator or small, cabinet-specific roller such as Whizz Velour brand. Larger areas may not level with a hand application.
  • If a faster build is desired when applying clears over raw wood, use General Finishes Sanding Sealer for the first coat, followed by 2 coats of Enduro Conversion Varnish.
  • Finish sand between coats with a fine-grade (220-320) foam sanding pad to improve smoothness and adhesion.
  • Remove dust with a vacuum, compressed air, an oil-free tack cloth, or a water-dampened rag.

SKU: CVF

Customer Reviews

No reviews yet
0%
(0)
0%
(0)
0%
(0)
0%
(0)
0%
(0)