Osmo Polyx-Oil Original - 0.75L

Osmo Polyx-Oil is a general-purpose Hardwax-Oil wood finish that uniquely combines the advantages of natural oils and waxes in one product. It is stain-resistant, water repellent, and abrasion-resistant and results in a surface that is pleasant to the touch. In comparison to conventional finishes, the use of plant ingredients creates a more even color and more harmonious appearance. 

This finish is derived from natural vegetable oils and waxes. Resistant to water, dirt, beer, wine, cola and saliva, Osmo Polyx-Oil is microporous and molecularly bonds with the wood, meaning it does not crack, flake, peel or blister.

The advanced formula of Polyx-Oil has been specially engineered in Germany to be the first Hardwax-Oil available on the North American market that can be easily applied with a brush or roller, with no buffing necessary! Can be spot-repaired and/or restored/renewed with no sanding required, therefore wood never needs complete sanding and refinishing again.

Also available in 0.125L and 2.5L sizes. For an untreated appearance, use Osmo Polyx-Oil Raw Matte.

Don't forget your brushes and pads!

Note: Oils enhance the natural tone of wood (permanent wet effect). Applying the product too generously and insufficient ventilation lead to delays in drying.

[TABS]

Features

• Easy to apply – used by both professionals and homeowners
• Extremely durable and hardwearing
• Can be spot-repaired and refreshed with no sanding required
• Microporous finish which does not crack, peel or flake
• Resistant to water and dirt as well as juice, tea, cola, wine, beer, coffee
• Enhances the wood’s natural character
• Saliva-resistant and sweatproof, suitable for children’s toys

Specs

Coverage rate: 194 sq. ft.
Number of coats: 2 coats
Application temp.: 41°F - 95°F (5°C to 35°C)
Approx. drying time: 8-10 hours*
Full cure time: 2-3 weeks

*Lower temperatures and/or higher air humidity can increase the drying time. Ventilate well while drying.

Directions (Pad)

• Stir the Polyx-Oil well and pour into tray
• Work the product into the wood thinly and evenly in figure 8 or circular motions using the fleece applicator pad
• Be sure to thinly and evenly coat the surface and leave on the surface for approx. 5 minutes
• Allow approx. 8-10 hours drying time. Allow for good ventilation whilst drying
• Apply second coat following previous steps.

Directions (Brush/Roller)

First Coat: Apply one thin coat with an Osmo Floor Brush or Osmo Floor Roller. Our rollers have a 4.5mm nap.

• Stir the Polyx-Oil well and prior to use
• Brush or roll the product thinly and evenly onto the floor
• Do not remove excess product, this will absorb into the wood surface over the drying period
• Allow 8-10 hours drying time prior to proceeding to second coat

• Brush or roll the second coat thinly and evenly onto the floor
• Allow approximately 5-10 minutes for product to penetrate surface
• Allow 8-10 hours drying time. Allow for good ventilation whilst drying

Third Coat: Usually a third coat is not required, however highly absorbent or dry timbers may appear to require a third coat.

Please consult OSMO technical support at 1-844-OSMOCAN prior to carrying out a third coat

Tinting: Osmo Wood Wax Finish can also be used to lightly tint Polyx-Oil 3054 up to a ratio of 10:1. Do not exceed a ratio of 10 parts Polyx-Oil 3054 to 1 part Wood Wax Finish.

Cure Period: Osmo Hardwax-Oil(s) like all floor finishes have a cure period. We recommend allowing 2 weeks for the surface to fully cure and harden prior to damp-mopping or placing rugs/mats on the surface.

Video

[/TABS]